Technical characteristics
Lacing system Open hook + webbing
Blocking hook
Rubber stone guard at the front of the boot
Waterproof, breathable membrane
EVA midsole + soft PAD
PU heel insert
Outsole: ForclazDesign Vibram® sole with thick and deep spikes.
Lining composition: textile
Upper composition: high resistance Matryx®EVO textile
Weight: 620 g
Medium fit footwear
Made in Europe
Benefit of the self-locking hook
With this material, you can separate the upper and lower lacing
This allows you to adjust the lacing to the shape of your foot and give your ankle as much freedom as you like. To separate the upper lacing from the lower part, make a simple knot level with your instep or use your shoes’ self-locking hook.
All of our trekking shoes have this feature.
VIBRAM®. Grip and traction of our soles
Our VIBRAM® branded soles provide excellent grip on all dry, earth or rocky terrain.
Just awesome! The VIBRAM® notching also gives you grip adapted to muddy or wet terrain.
Medium width sole: the wider the sole, the softer it is.
Therefore, with this sole it’s comfortable to walk on most trails without losing stability.
MATRYX® EVO technology
The most used part of the upper on the ground has MATRYX® EVO fabric, this is jacquard with integrated lining. Technical compound of a PA warp coated with 550DTEX PU and a PA weft coated with 550DTEX PU.
167Dtex PES lining.
Aramid yarn throughout the upper to ensure good support and high resistance to abrasion on the areas of the boot most sensitive to rubbing.
This boot’s waterproof level
This boot has been tested and validated for 50,000 flexes repeatable, equivalent to a 20 km walk, in water reaching the mid-upper. This now guarantees a good level of boot waterproofing.
--> Our assessment indicates a LEVEL OF 4/5 giving 8 hours of waterproofing when hiking in the rain.
The details of tests carried out to assess the waterproofing of our boots is below.
Increase your boot’s waterproofing with a gaiter
The waterproofing of boots is often compromised because water gets in at the collar of the boot.
--> To keep your feet dry for longer, it is advisable to use a waterproof gaiter or mini-gaiter that will prevent water as well as pebbles and sand from getting inside through the top of the boot.
Model perfectly suited to this trekking gaiter MT500 black
Make the waterproofing of this textile model last longer
Even though this model has a membrane (waterproof, breathable), it is recommended you use a re-waterproofing spray a few times a year to restore the original water-repellent properties and prevent staining of the outer material.
--> It revitalises the water-repellent properties of the outer material (water runs off and doesn't soak in). Each fabric section is sprayed taking care not to forget the thread in the seams (water loves seams!!)
Waterproofing my textile boots with a reactivating spray
1/ Use a brush and/or sponge to clean and remove any dirt or mud.
2/ Then leave to air dry, away from any heat source.
3/ Shake the WATERPROOF SPRAY can €5
4/ Spray the product from a distance of 25 cm
5/ Leave for at least 10 minutes.
Caution: Do not rub or wipe.
We recommend our water-repellency reactivating spray
Main complementary laboratory tests
Laboratory tests were conducted to test the following elements:
- tearing of the eyelets and straps
- bonding of the sole
- toxicology
- UV-resistance
- abrasion of the sole and components of the upper
- accelerated ageing
Use with strap-on crampons only
This model of trekking boot allows for the occasional use of strap-on crampons only. It is sufficiently rigid for the occasional use of strap-on crampons while guaranteeing extremely good comfort when walking.
Choosing your size is an important point.
For hiking, do not hesitate to buy one size larger than the usual size to guarantee excellent comfort on the descent and to avoid toes rubbing at the tip of the shoe. Tip: keep your toenails short and, before descending, check that your lacing prevents your foot from sliding forwards inside the boot.
Waterproofing test carried out on this model
Our boots are laboratory tested by 2 consecutive tests.
Test 1: We test the effectiveness of the membrane alone immersed in water under air pressure. We simply check for any bubbles on the surface like a pierced air chamber.
Test 2: Thanks to a mechanical arm that simulates walking, the entire boots are half immersed in water and they complete thousands of flexes to check that the inside of the boot remains dry and it is therefore waterproof.
5 levels of waterproofing
During the waterproofness test, we test 5 levels of waterproofness:
- 2,000 flexes (approximately 4 km, 30 minutes of walking)
- 10,000 flexes (approximately 10 km, 3 hours of walking)
- 30,000 flexes (approximately 15 km, 6 hours of walking)
- 50,000 flexes (approximately 20 km, 8 hours of walking)
- 100,000 flexes (approximately >20 km, 24 hours of walking)
Try your boots out step by step
How to choose your boots:
1. Try on both shoes, standing up, with the socks worn for hiking.
2. Tighten the laces correctly.
3. Check the following two areas of comfort: the base of the heel and the front part of the foot going down.
4. Stand up to walk with the boots on.
5. Try on several sizes and several models.
6. Break in your boots gradually during their first hikes to adapt them to your foot
