Product certified by independent technical inspection: Type 2 of the standard ISO 6185.
This product is not intended for use by children under 12 years of age.
Teenagers from 13 to 17 years old must only use this product under the direct supervision of an adult.
Always wear a life jacket.
Refer to the local regulations and information about the dangers of float tubes and navigation.
Maximum load: 160 kg
Maximum motor power: 300 Watts

The bag contains:
- the float tube (the 2 side bladders and the central platform are equipped with Bravo valves)
- the raised, ergonomic and adjustable seat is made of an aluminium structure, mesh and an EVA pad for quick drying
- 2 500 L storage bags: volume 10 L / 39.5 x 23.5 x 12 cm to store your fishing accessories
- ventilated carry bag
- user guide and user manual
- repair kit without glue (3 tarpaulin patches and a Bravo valves key)

The FLTB-9 is pre-equipped to add the FLTB MTR motor only (8666881 not included)
The motor can be quickly and easily clipped onto the base under the seat.
The wire guides on each side of the seat allow you to easily connect the motor to the battery (not included), which must be stored in a watertight storage bag. (not included)
You now just have to position the control unit within reach.

The following compatible accessories will make your fishing outings more comfortable: (not included)
> The FLTB SES (8560034) can be connected to the 2 side bases: depth sounder support to easily install your electronics.
> The side D-rings are used to attach:
- FLTB KPN (8737484): floating keepnet to keep your catch
- FLTB SDC (8560032): rod rack to transport your 4 sets in complete safety
> A range of modular storage bags for your fishing accessories.

Inflate the central dropstitch section to 10 PSI/0.7 bar, then the tubeless side bladders to 5 PSI/0.35 bar to avoid any risk of over-inflation and/or explosion.
We recommend using the pump FLTB PLP 10 PSI (ref: 8643922) equipped with a built-in pressure gauge. (not included)
Assemble the 2 side hoops in the seat base.
Adjust the straps for optimal comfort.
Clip the rear of the seat into the 2 notches and secure with the rip-tabs at the font and rear.

Remove the seat then deflate the float tube by unscrewing the valves.
Fold the left side of the float tube onto the central part, then repeat with the right side.
Fold in two lengthways.
Insert the float tube into the storage bag with the seat.
Once dry, your FLTB-9 can be stored folded inside the carry bag.
You will extend its lifetime by storing it flat and slightly inflated.

> FLOAT TUBE FLTB-9: 120 x 170 cm (width x length)
Diameter of the side bladders 35 cm
Weight: 13 kg (seat and inflatable structure)
Pouch on the rear of the seat (not watertight): 30 x 14 cm (width x height)
> SEAT:
- dimensions of the seat: 44 x 42 x 42 cm (width x depth x height)
- total dimensions when installed: 65 x 53 x 50 cm (width x depth x height)
> 500 L storage bag: 39.5 x 23.5 x 12 cm / volume: 10 L
> CARRY BAG: 80 x 55 x 35 cm

The following parts are available on this web site or in our stores (to order):
8665318 FLTB-9 CARRY BAG
8854162 FLTB-9 SEAT
8552219 HIGH PRESSURE VALVE
8640993 BAKKAN 500 L
For all work on the inflatable surfaces (to repair tears) and the valves (replacement), you are advised to take your float tube to a DECATHLON store, so that our central workshops can perform a diagnostic and make the necessary repairs.